Home Msbte Diploma Civil 22306 Strength of Materials Mcq Questions and Answers pdf

22306 Strength of Materials Mcq Questions and Answers pdf

0
872
Strength of Materials Mcq Questions and Answers pdf

Hello students welcome to msbte news in this article we have provided 22306 Strength of Materials Mcq Questions and Answers pdf. This Msbte Strength of Materials Mcq Question Bank is ideal for Students who are in Secod Year of Diploma in Mechanical, Automobile and Prodcution Technology Engineering courses. By referring Msbte Strength of Materials Mcq Pdf for Diploma you will get to know about the paper pattern of Msbte Mcq Winter 2021 exams.

with this Strength of Materials Mcq for Mechanical Engineering, Automobile and Prodcution Technology 2nd year students can practice for their upcoming Winter 2021 exams. In this Strength of Materials Multiple Choice Questions we have selected 30 important questions from previous year papers. you can also download Strength of Materials Pdf below we have given a download link.

Strength of Materials Mcq Questions and Answers

1) The moment of inertia of a triangular section of base 3 unit and height 2 unit, about an axis passing through its base is ___. 
a. 6
b. 9
c. 8
d. 2

Correct!

Wrong!

2) Moment of inertia of a square of side 1 unit about an axis through its center of gravity is ____. 
a. 1
b. 1/12
c. 1/3
d. 1/4

Correct!

Wrong!

3) The axis about which moment of area is taken is known as ____________. 
a) Axis of area
b) Axis of moment
c) Axis of reference
d) Axis of rotation

Correct!

Wrong!

4) The increase in the length of a bar of length 1 m, area 300 mm2, modulus of elasticity 2×10^5 N/mm2 due to a tensile load of 120 KN is _____. 
a. 1 mm
b. 2 mm
c. 3 mm
d. 4 mm

Correct!

Wrong!

5) Shear stress causes____. 
a. deformation
b. elongation
c. contraction
d. None of above

Correct!

Wrong!

6) Which of the following has the same unit? 
a. modulus of elasticity, pressure, stress
b. elasticity, strain, stress
c. pressure, strain, stress
d. modulus of elasticity, strain, modulus of rigidity

Correct!

Wrong!

7) In a simply supported beam carrying a uniformly distributed load W/m over the left half span, the point of contraflexure will occur in 
(a) Left half span of the beam
(b) Right half span of the beam.
(c) Quarter points of the beam
(d) Does not exist

Correct!

Wrong!

8) A sudden increase or decrease in shear force diagram between any two points indicates that there is 
(a) No loading between the two points
(b) Point loads between the two points
(c) U.D.L. between the two points
(d) None of these

Correct!

Wrong!

9) When the bending moment is a parabolic curve between two points, it indicates that there is 
(a) No loading between the two points
(b) Point loads between the two points
(c) U.D.L. between the two points
(d) Uniformly varying load between the two points

Correct!

Wrong!

10) A beam is said to be of uniform strength, if ____________ 
a) B.M. is same throughout the beam
b) Shear stress is the same through the beam
c) Deflection is the same throughout the beam
d) Bending stress is the same at every section along its longitudinal axis

Correct!

Wrong!

11) In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is 
a. Wl at the free end
b. Wl at the fixed end
c. Wl/2 at the fixed end
d. Wl at the free end

Correct!

Wrong!

12) In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is 
a. Wl/8 or wl2/8 at the mid-point
b. Wl/8 or wl2/8 at the end
c. Wl/4 or wl2/4
d. Wl/2

Correct!

Wrong!

13) A simply supported beam carries a uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? 
a. 5.4 mm
b. 1.08 mm
c. 6.2 mm
d. 8.6 mm

Correct!

Wrong!

14) In the cantilever beam, slope and deflection at free end is _____ 
a. zero
b. maximum
c. minimum
d. none of the above

Correct!

Wrong!

15) Deflection of a simply supported beam when subjected to central point load is given as ________ 
a. (Wl /16 EI)
b. (Wl2 /16 EI)
c. (Wl3 /48 EI)
d. (5Wl4 / 384EI)

Correct!

Wrong!

16) The load at which a vertical compression member just buckle is known as 
(a) Critical load
(b) Crippling load
(c) Buckling load
(d) Any one of these

Correct!

Wrong!

17) A column that fails due to direct stress is called 
(a) Short column
(b) Long column
(c) Medium column
(d) Slender column

Correct!

Wrong!

18) A column whose slenderness ratio is greater than 120 is known as 
(a) Short column
(b) Long column
(c) Medium column
(d) Composite column

Correct!

Wrong!

19)  If load is acting on the longitudinal axis of the column, it is called _____________. 
(A) Horizontal load
(B) Axial load
(C) Eccentric load
(D) Vertical load

Correct!

Wrong!

20) If the load is acting away from the longitudinal axis of the column, it is called _____________. 
(A) Horizontal load
(B) Axial load
(C) Eccentric load
(D) Vertical load

Correct!

Wrong!

21) The horizontal distance between the longitudinal axis of column and the line of action of load is called ______________. 
(A) Eccentricity
(B) Axial distance
(C) Vertical distance
(D) None of these

Correct!

Wrong!

22) The plane, on which only direct stress is acting is called ______________. 
(A) Principal stress
(B) Horizontal Plane
(C) Principal Plane
(D) Vertical Plane

Correct!

Wrong!

23) On the Principal plane, shear stress is ___________. 
(A) Zero
(B) Maximum
(C) Minimum
(D) Infinity

Correct!

Wrong!

24) Principal plane may be 
(A) Vertical
(B) Horizontal
(C) Inclined
(D) Vertical, horizontal or inclined

Correct!

Wrong!

25) shaft is said to be in pure torsion if 
a. Turning moment is applied at one end and the other end is free
b. Turning force is applied at one end and the other end is free
c. Two opposite turning moments are applied to the shaft
d. Combination of torsional load and bending load is applied to the shaft

Correct!

Wrong!

26) In power transmission equation, P=2ΠNT/60×1000 
a. P is in kw and T is maximum torque
b. P is in NM/sec and T is maximum torque
c. P is in NM/sec and T is mean torque
d. P is in kw and T is mean torque

Correct!

Wrong!

27) If diameter of a shaft is doubled the power transmitted capacity will be 
a. Either twice or half
b. Four times
c. Eight times
d. Same

Correct!

Wrong!

28) The impact strength of a material is an index of its 
(a) toughness
(b) tensile strength
(c) capability of being cold worked
(d) hardness

Correct!

Wrong!

29) The property of a material which allows it to be drawn into a smaller section is called 
(a) plasticity
(b) ductility
(c) elasticity
(d) malleability

Correct!

Wrong!

30) The property of a material by virtue of which it can be beaten or rolled into plates is called 
(a) malleability
(b) ductility
(c) plasticity
(d) elasticity

Correct!

Wrong!

Share the quiz to show your results !

Subscribe to see your results

22306 Strength of Material Mcq Questions 1

I got %%score%% of %%total%% right

%%description%%

%%description%%

Loading…

22306 Strength of Materials Mcq Pdf for Diploma

Msbte News Social accounts

We provide regular updates about msbte on our social accounts For latest msbte diploma updates you can follow our page on Instagram @msbtenews and Facebook @msbtediplomaupdates. we solve your queries by message on our social accounts so do follow our social accounts if you have any queries related to diploma and engineering courses. 

Latest Diploma Jobs (View Here)

Thankyou for Visiting Msbte News.

msbte news.com is created to help msbte diploma students to find study resources, which are very much needed for diploma students while preparing for the exam. msbtenews.com will provide all msbte mcq question bank with answers which are provided by msbte.org.in. with these model question and answer papers students gets a rough idea about paper pattern and marks distribution.

No comments

Leave a reply

Please enter your comment!
Please enter your name here